Product Information. https://washingtontree830.weebly.com/blog/download-revit-wall-types. Bold, sleek and sporty, the Casio SGW100-1V wrist watch for men is sure to go with your attire and personality. https://washingtontree830.weebly.com/blog/microsoft-flight-sim. Engineered with Quartz movement, this Casio men watch keeps you updated with accurate time and date display.
3
•If you want to cancel bearing sensor correction, press D in step 5 instead of C.
This will return to the screen in step 2. From there you can press A to exit the
•The indicator will go around the display up to four times, if you do not stop it by
pressing C. After the fourth time, the watch will exit the calibration screen
To perform magnetic declination correction
1.In the Digital Compass/Thermometer Mode, hold down
A until the indicator at the 12 o’clock position starts to
2.Press C.
declination angle direction will flash on the display.
declination angle and magnetic declination angle
Magnetic
angle value
declination
•You can select a value within the range of 90° W to 90°E with these settings.
•The following explains magnetic declination angle direction settings.
0 OFF: No magnetic declination correction performed.The magnetic
E: When magnetic north is to the east (east declination)
W: When magnetic north is to the west (west declination)
•You can turn off (0 OFF) magnetic declination correction (which effectively makes
the magnetic declination angle: 0°) by pressing D and B at the same time.
•The illustration, for example, shows the value you should input and the direction
setting you should select when the map shows a magnetic declination of 1° West.
4. When the setting is the way you want, press A to exit the setting screen.
Using the Digital Compass While Mountain Climbing or Hiking
This section describes three real-life situations where you could use the watch’s built-
•To set a map and find your current location
Having an idea of your current location is important when mountain climbing or
hiking. To do this, you need to “set the map”, which means to align the map so the
directions indicated on it are aligned with the actual directions of your location.
Basically what you are doing is aligning north on the map with north as indicated by
•To find the bearing to an objective
1.With the watch on your wrist, position it so the face is
2.In the Timekeeping Mode, press D to take a compass
•The reading will appear on the display after about two
3.Rotate the map without moving the watch so the
northerly direction indicated on the map matches north
![]()
•If the watch is configured to indicate magnetic north,
indication. If the watch has been configured with a
declination to correct to true north, align the map’s
•This will position the map in accordance with your
4.Determine your location as you check the geographic
Current
N
North indicated
North indicated by
To find the bearing to an objective
1.Take a compass reading and then set the map so its
northerly indication is aligned with north as indicated by
•See “To set a map and find your current location” for
2.Set the map so the direction you want to travel on the
3.With the watch on your wrist, position it so the face is
4.In the Timekeeping Mode, press D to take a compass
•The reading will appear on the display after about two
5.Still holding the map in front of you, turn your body until
direction on the map are aligned.
•This will position the map relative to your current location, so the bearing to your
12 o’clock
N
Current
Objective
Question:What causes incorrect direction readings?
Casio Sgw 100 Manual Pdf
•Nearby source of strong magnetism, such as a household appliance, a large steel
bridge, a steel beam, overhead wires, etc., or an attempt to perform direction
measurement on a train, boat, etc. Move away from large metal objects and try
again. Note that digital compass operation cannot be performed inside a train, boat,
Question:What causes different direction readings to produce different results
Answer: Magnetism generated by nearby high-tension wires is interfering with
detection of terrestrial magnetism. Move away from the high-tension wires
Question:Why am I having problems taking direction readings indoors ?
Answer: A TV, personal computer, speakers, or some other object is interfering with
terrestrial magnetism readings. Move away from the object causing the
interference or take the direction reading outdoors. Indoor direction readings
are particularly difficult inside ferro-concrete structures. Remember that you
will not be able to take direction readings inside of trains, airplanes, etc.
World Time displays the current time in 48 cities (29 time
•If the current time shown for a city is wrong, check your
changes.
•All of the operations in this section are performed in the
To view the time in another city
In the World Time Mode, use D (east) to scroll through
•For full information on city codes, see the “City Code
Timekeeping
Current time in the zone
City code
To toggle a city code time between Standard Time and Daylight Saving Time
1.In the World Time Mode, use D (east) to display the
city code (time zone) whose Standard Time/Daylight
2.Hold down A to toggle between Daylight Saving Time
indicator not displayed).
•The DST indicator appears on the display whenever you
display a city code for which Daylight Saving Time is
•Note that the DST/Standard Time setting affects only the
currently displayed city code. Other city codes are not
DST indicator
The stopwatch lets you measure elapsed time, split times,
•The display range of the stopwatch is 59 minutes, 59.99
•The stopwatch continues to run, restarting from zero
•The stopwatch measurement operation continues even
•Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
•All of the operations in this section are performed in the
Minutes
1/100 second
To measure times with the stopwatch
DDDDA
Split Time
StartSplitSplit releaseStopClear
Casio 3157 Manual
DADAA
JJJJ
First runner
Display time of
Display time of
Second runner
JJJJ
Countdown Timer
You can set the countdown timer within a range of one
minute to 24 hours. An alarm sounds when the countdown
•You also can select auto-repeat, which automatically
restarts the countdown from the original value you set
•All of the operations in this section are performed in the
C.
HoursMinutes
To configure countdown start time and auto-repeat settings
1.While the countdown start time is on the display in the
setting of the countdown start time starts to flash, which
•If the countdown start time is not displayed, use the
display it.
2.Press C to move the flashing in the sequence shown
(Minutes)
On/Off
(Hours)
3.Perform the following operations, depending on which
•While the start time setting is flashing, use D (+) and
Auto-repeat on indicator
0:00
•While the auto-repeat on/off setting (0N or 0FF) is flashing on the display, press
4. Press A to exit the setting screen.
) is displayed on the Countdown Timer Mode
•Frequent use of auto-repeat and the alarm can run down battery power.
1
Getting Acquainted
Congratulations upon your selection of this CASIO watch.To get the most out of your
Applications
The built-in sensors of this watch measure direction and temperature. Measured
values are then shown on the display. Such features make this watch useful when
hiking, mountain climbing, or when engaging in other such outdoor activities.
•The measurement functions built into this watch are not intended for use in taking
measurements that require professional or industrial precision. Values produced
by this watch should be considered as reasonably accurate representations only.
•When engaging in mountain climbing or other activities in which losing your way
can create a dangerous or life-threatening situation, always be sure to use a
•Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any
damage or loss suffered by you or any third party arising through the use of this
About This Manual
•Depending on the model of your watch, display text
appears either as dark figures on a light background or
light figures on a dark background. All sample displays
in this manual are shown using dark figures on a light
•Button operations are indicated using the letters shown
•Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
(Light)
General Guide
•The illustration below shows which buttons you need to press to navigate between
•In any mode (except when a setting screen is on the display), press B to illuminate
•You can enter the Digital Compass/Thermometer Mode from the Timekeeping Mode
by pressing D. To enter from another mode, first use C to enter the Timekeeping
Stopwatch Mode
Countdown Timer
Alarm Mode
Timekeeping Mode
Thermometer Mode
▲
Press C.
▲
▲
Timekeeping
Use the Timekeeping Mode to set and view the current
Read This Before You Set the Time and Date!
This watch is preset with a number of city codes, each of
which represents the time zone where that city is located.
When setting the time, it is important that you first select
the correct city code for your Home City (the city where
you normally use the watch). If your location is not
included in the preset city codes, select the preset city
code that is in the same time zone as your location.
•Note that all of the times for the World Time Mode city
codes are displayed in accordance with the time and
date settings you configure in the Timekeeping Mode.
Month – Day
Seconds
1. In the Timekeeping Mode, hold down A until the city code starts to flash, which
2. Use D and B to select the city code you want.
•Make sure you select your Home City code before changing any other setting.
•For full information on city codes, see the “City Code Table”.
3. Press C to move the flashing in the sequence shown below to select the other
Second
12/24-Hour
Minute
Month
Temperature
City Code
•The following steps explain how to configure timekeeping settings only.
4. When the timekeeping setting you want to change is flashing, use D and/or B to
To do this:
Toggle between Daylight SavingTime
) and Standard Time ().
12H
24-hour (
) timekeeping.
00
Do this:
(west).
Press D.
Use D (+) and B (–).
5. Press A to exit the setting screen.
•For details about configuring temperature display settings, see “To specify the
•See “Daylight Saving Time (DST) Setting” below for details about the DST setting.
Change the month or day
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
To toggle the Timekeeping Mode time between DST and Standard Time
1. In the Timekeeping Mode, hold down A until the city
code starts to flash, which indicates the setting screen.
2. Press C once and the DST setting screen appears.
3. Press D to toggle between Daylight Saving Time (
displayed) and Standard Time (OFF displayed).
•The DST indicator appears to indicate that Daylight
DST indicator
Digital Compass/Thermometer
You can take direction readings and temperature readings in the Digital Compass/
Direction readings are taken by the watch’s built-in magnetic bearing sensor and
displayed as one of 16 directions. A temperature sensor is used for temperature
•See “Digital Compass” for more information about the digital compass.
•See “Thermometer” for more information about the thermometer.
To enter and exit the Digital Compass/Thermometer Mode
1. While in the Timekeeping Mode, press D to enter the
•The watch will start to take direction and temperature
readings. After about two seconds, the direction that
the 12 o’clock position of the watch is facing will be
indicated and the current temperature reading will
•Direction readings will be taken each second for about
•Temperature readings will be taken every two
automatically.
•To perform direction and temperature readings for
2. Press C to return to the Timekeeping Mode.
•For information about using the digital compass, see “To
•For information about using the thermometer, see “To
12 o’clock position
During readings
About two
Thermometer
The watch takes temperature readings automatically whenever you enter the Digital
Compass/Thermometer Mode. In addition, you can take readings manually by
•You can calibrate the temperature sensor if you think readings are wrong for some
•You can select either Celsius (°C) or Fahrenheit (°F) as the temperature unit.
Summary of content (5 pages)Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |